Static Control: Abandon dynamic control and return to Dynamic Control screen. The reflector is adjusted so that a light beam from the detector, directed across the line, is reflected back into a photocell in the detector. Ink Temp: Range: 5--55 C, depending upon ink type. Provides access to the message store and is closely linked with the Message Editor. Note: The 4000 hour service kit is part number 30470. For further details and fitting instructions see the air driven airdryer appendix Domino part number 20950. Also, by pressing the down cursor key, the screen changes to give software details.
Domino would be pleased to assist with any problem. It is bolted onto the rear of the printer. Alternatively the fan can be replaced as follows: Inline Connectors Heatsink. The major and minor denominations are carried as the upper and lower case currency key entries. Too much make--up Make--up level is above maximum. Test your skills in quick play or tackle your way through carehimmelblau manual 6th edition domino a100 inkjet printer manual algebra self guide domino a100 printer. Function key options: Cancel Discontinue procedure.
Check compressor motor, piston seal and valve plates. However, the cables must be connected again when the cover is refitted to the box. The gutter system in the head consists of the gutter pipe, a short length of tube, and a gutter sensor consisting of a length of pipe electrically isolated from the chassis. Where they appear next to a procedure or instruction, they have the significance and importance of written warnings and cautions. Options: explaining the options where these are not immediately apparent Function key options: explaining the options offered through the soft keys. Protective clothing especially safety glasses. Carefully push the cable gland on the wiring into the bulkhead seal.
This environment around the jet and gutter ensures that the ink does not absorb airborne contaminants which are the main cause of ink degradation. Fuses F1 and F3 Fuse F2 are 4A T power fuses. Lint free tissue to catch any escaping ink. Domino can provide further information and advice. Message Store Provides access to the stored Messages. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Note that to work correctly, the gutter sensor must be completely electrically isolated except for its wiring connections.
For further details and fitting instructions see the air driven airdryer appendix Domino part number 20951. Domino A--Series printers should be mounted on a stand or fitted with a stabiliser kit see Part 10 : Options. Page 7--3 Ink System -- Access. The tube from the orifice to the humidity sensor should be replaced with tube cut to a suitable length to: a Point directly at the sensor. Note: For details of the print head see pg. The distance between strokes is sometimes used as a unit of measurement in spacings or delays. Save as Default Retain new names for use in new messages.
Notes 1 The part number for the airdryer test kit used in this check is 30455. For details of access to the ink system see pg. Solvent on deflector plates after cleaning. Note: In dusty environments, the filter should be replaced more frequently. Excess pump overspeed Ink pressure is being maintained but pump speed is excessive. To protect against escaping ink, place tissue around the nozzle plate before releasing the securing screws, or around an ink feed tube junction before disconnection.
The supply must be free from electrical noise. Text Field Length: Enter length in character widths. Page 8--3 Nozzle Plate Removal and Cleaning. Head not mounted at 90 degrees to direction of product movement. The airdryer circuits perform the following functions: Provide power to the Peltier cooling element Maintain the Peltier cool side at or above 4 C to prevent icing of the cooler in low ambient temperatures Periodically open the condensate drain solenoid Periodically sample the output air pressure and humidity, and if.
If a fused power connector is not used, then the supply circuit should have a circuit breaker or fuse rated at 5A. To replace the air filter, pull out the old filter situated at the side of the electronics compartment and slide in the new filter, making sure that it is fitted in the same orientation as the old one with tab at the bottom. Check that nozzle is not blocked. The holster is mounted in the printing position and contains precision guide rails to ensure that the print head always returns to exactly the same position if the print head is removed and replaced. Print Head Cleaning The printer must be shut down. Peltier chamber Check solenoid operation. Pressure sensor input error Failure at input to sensor.
If it does not, ensure that all parts are removed from the recess. Check and reset pressure if required. Carefully push the cable glands out of the bulkhead seal in the direction of the drop generator. If the real master clock time is required, one of the clocks should be left with zero offsets. . Description 37735 Solenoid Cable Assembly 37752 Ink Management Block Assembly 37733 Viscometer Assy 14453 Filter Nut for 14831 14831 Filter 5 Micron 37753 Ink Manifold Assembly 29265 Filter Kit No. Description 26898 Drive Rod Cap 26868 Nut Drive Rod Clamp 26856 Drive Rod Assembly Pinpoint 26747 Drive Rod Assembly Refer also to ink type conversions in Part 10 : Options 04368 Screw Skt Cap St.
Domino can also provide mountings for the print head from a range of brackets and support systems. Domino will provide advice on an appropriate encoder. Stroke control is directly selectable as internal or external external is normally a shaft encoder. The adjustment is only effective with internal stroke generation. Cabinet temperature sensor input error Failure at input to sensor. When the tubes and ring nut are removed, the regulator can be lifted out and replaced. Counted Products Opens Counted Products screen --see below.